What Is Polypropylene Plastic

Polypropylene plastic is a semi-crystalline thermoplastic polyolefin, polymerised from propylene gas and sold as pellets. It is the second-largest commodity thermoplastic by volume once the polyethylene grades are counted as one family.

The base polymer is cleared for food contact in the US under 21 CFR 177.1520. BPA is a building block of polycarbonate and of epoxy can linings, while polypropylene is polymerised from propylene alone. What differs between two PP articles is the additive package and the converting, both of which the buyer specifies.

Polypropylene is also assigned resin identification code 5.

What Polypropylene Plastic Is Made Of and How It Is Made

Polypropylene is made from a single monomer, propylene, a gas recovered from the steam cracking of refinery gas and the catalytic cracking of heavy oil, with propane dehydrogenation as the third route.

Nearly all commercial PP is polymerised on heterogeneous Ziegler-Natta catalysts. Metallocenes are the single-site alternative, with tighter control of molecular weight, end groups and stereoregularity.

The methyl groups can take several spatial arrangements along the chain, and only the isotactic form, with all of them on the same side, is marketed in significant quantity.

The resin leaves the reactor as powder. It is homogenised in a twin-screw extruder, cut into pellets under water, and blended by lot before it ships.

Properties of Polypropylene Plastic

Polypropylene is semi-rigid: stiffer and harder than polyethylene, with a higher melting point, and more flexible than ABS or nylon — where it sits among the commodity plastics.

PropertyTypical homopolymer valueTest method
Density0.905 g/cm³ISO 1183
Melting point160–165 °CISO 3146
Flexural modulus1,200–1,450 MPaISO 178
Tensile strength at yield30–33 MPaISO 527-2
Heat deflection temperature100 °C at 0.45 MPa; 55 °C at 1.80 MPaISO 75-2
Notched Charpy impact, 23 °C6 kJ/m²ISO 179
Melt flow rate3 g/10 min (general-purpose grade)ISO 1133, 230 °C / 2.16 kg

At 0.905 g/cm³ polypropylene is the lightest of the commodity plastics.

Service temperature is far below the melting range. A loaded PP part runs continuously between 0 and 80 °C, and reaches about 100 °C only where it carries no significant mechanical stress.

Melt flow rate is most of what a PP grade code tells you.

Two MFR figures taken at different loads or temperatures never belong in the same column, and the two standards are not interchangeable either — ASTM D1238 notes that it and ISO 1133 address the same subject but differ in technical content. Check which standard a certificate of analysis was written against before you set it beside a datasheet.

What Are the Downsides of Polypropylene

Polypropylene’s downsides are low-temperature brittleness, UV sensitivity, oxidation, mould shrinkage and flammability. Each takes a standard correction, either a grade change or an additive package, and none of them calls for a different polymer.

  • Low-temperature brittleness: the homopolymer’s notched Charpy is 6 kJ/m² at 23 °C. An extrusion-grade heterophasic copolymer still returns 8 kJ/m² at −20 °C, but read the impact row at your own temperature.
  • UV sensitivity: unpigmented PP discolours and loses mechanical properties outdoors. UV absorbers, light stabilisers or carbon black extend it.
  • Oxidation: the tertiary carbon on every second backbone atom is where thermal degradation begins. Every commercial grade carries an antioxidant package.
  • Mould shrinkage and warping: shrinkage is high for a commodity thermoplastic and direction-dependent. Nucleation and mineral filler, usually talc or glass fibre, are the standard corrections.
  • Flammability: with a limiting oxygen index around 17, PP burns readily in air. Flame-retardant grades exist for the applications that require a classification.

The Three Types of Polypropylene

The three commercial types are homopolymer, random copolymer and impact (heterophasic) copolymer. They are separated by comonomer — what is fed to which reactor.

TypeWhat is polymerisedWhat it changesWhere it goes
HomopolymerPropylene aloneHighest stiffness and melting point, weakest impact below room temperatureRaffia tape, BOPP film, fibre, general injection moulding
Random copolymerPropylene with 0.1–8 mol% ethylene in the same reactorStays single-phase, so clarity rises and the melting point falls; softerClear containers, hot- and cold-water pipe
Impact copolymerHomopolymer first, then an ethylene-propylene rubber phase in a gas-phase reactorLow-temperature impact strength, paid for in stiffness and clarityCrates, automotive parts, cold-store packaging

PP compounded after the reactor with a bought-in elastomer is a separate product on a separate route.

What Is Polypropylene Plastic Used For

Polypropylene is converted on every commodity route — injection moulding, film, fibre, pipe and sheet — and each route takes a different polypropylene grade, set first by melt flow and then by type.

Converting processTypical productsType usually specified
Injection mouldingClosures with living hinges, thin-wall containers, crates, automotive interior and under-bonnet partsHomopolymer for thin-wall, impact copolymer for crates and automotive
FilmBOPP and CPP film for packaging and laminationHomopolymer
Fibre and raffiaWoven sacks and FIBC, spunbond nonwovens, carpet yarn, ropeHomopolymer
PipeHot- and cold-water pipe systems, specified by ISO 15874Random copolymer (PP-R)
Sheet and thermoformingCorrugated sheet, fabricated tanks and ductwork, thermoformed pots and cupsHomopolymer or copolymer sheet grades

Newsletter Updates

Enter your email address below and subscribe to our newsletter

Leave a Reply