Which HDPE Blow Molding Grade for Oil and Detergent Bottles

For detergent, household-chemical and motor-oil bottles, buy an HDPE blow molding grade that is an ethylene copolymer and screen it on an ESCR figure that states its test condition. Chevron Phillips, Formosa and INEOS list their bottle grades for these contents at a melt index of about 0.2–0.35 g/10 min at a 2.16 kg load and a density of about 0.946–0.958 g/cm³.

The bottle’s contents then decide how much stress-crack resistance to buy and how to confirm it:

  • Detergent, bleach and household chemicals: a copolymer grade, compared on ASTM D1693 Condition B hours at a stated Igepal strength. Move to a higher-ESCR grade when the bottle is lightweighted or sits in hot summer storage.
  • Motor oil: the same copolymer grade family. Some producers sell one named grade for both bottles, but an ESCR figure measured in surfactant does not rate the grade against oil, so confirm it with bottles filled with the oil.
  • Milk, juice and water: a homopolymer grade. This is the one case where the answer above does not apply.

Copolymer or Homopolymer for Detergent and Oil Bottles

Use a copolymer grade for detergent and oil bottles; homopolymer HDPE belongs to milk, juice, water and other non-aggressive contents.

Melt Index for Detergent and Oil Bottles

A detergent or oil bottle grade should sit at about 0.2–0.35 g/10 min at a 2.16 kg load, where Chevron Phillips, Formosa and INEOS place the grades their bottle tables list for these bottles.

Check the load before comparing. Bottle grades print MI at 2.16 kg, while grades for large containers print it at 21.6 kg or 5 kg. OPaL’s B55H03, a grade for containers up to 100 L, prints 0.35 g/10 min at 5 kg and 9.00 g/10 min at 21.6 kg, so its 0.35 is a different number from a bottle grade’s 0.35 at 2.16 kg.

Density for Detergent and Oil Bottle Grades

Look for a density of about 0.946–0.958 g/cm³.

Take the lower end of the band when the contents crack bottles and the upper end when the bottle needs stiffness for top load. A bottle on a 0.954 g/cm³ grade that cracks in summer storage is a case for moving to about 0.950 g/cm³.

How Much ESCR a Detergent Bottle Grade Needs

A standard detergent bottle grade carries about 35–50 h of ESCR in ASTM D1693 Condition B, F50, at 100 % Igepal, which is where the grades sold for these bottles start. Compare grades only at the same Igepal strength:

Grade (producer)Sold forESCR F50, hCondition
Formolene HB5502A (Formosa)Bleach and detergents35D1693 Condition B, 100 % Igepal
Alathon L5440 (LyondellBasell)Household chemicals, detergent and motor-oil bottles50D1693 Condition B, 100 % Igepal
Marlex TRB-533 (Chevron Phillips)Household and industrial chemical containers>2,500D1693 Condition B, 100 % Igepal
Marlex TRB-533 (Chevron Phillips)Household and industrial chemical containers>1,000D1693 Condition B, 10 % Igepal

The figures come from Formosa’s HB5502A data sheet, LyondellBasell’s Alathon L5440 page and Chevron Phillips’ Marlex TRB-533 data sheet.

Many data sheets name the method and leave out the condition. Ask the supplier for it before comparing two grades.

Small gaps between sheets mean little. The inter-laboratory precision of D1693 is a factor of about 2.9 at two standard deviations. A 35 h grade and a 50 h grade are the same class; a several-fold gap is a real difference.

Go to the higher-ESCR grades when the bottle is lightweighted or stored hot. The next step up from 35–50 h is grades sold for lightweight detergent bottles at a few hundred hours: Chevron Phillips Marlex 9505H prints 250 h (Condition B, 100 % Igepal) and INEOS Rigidex HD5802BM more than 200 h at 50 °C in 100 % Igepal. Then settle whether a grade’s ESCR is enough with filled bottles of your own product under constant stress, by top load or internal pressure.

Does an Oil Bottle Need a Different Grade From a Detergent Bottle?

No: a motor-oil bottle runs on the same copolymer grade family as a detergent bottle, and some producers sell one named grade for both.

The difference lies in how the grade is rated. Hydrocarbons such as motor oil are absorbed into polyethylene and soften it, while surfactant solutions are not absorbed. That softening can mask or shift stress cracking, so an Igepal ESCR figure does not rank grades against oil. For an oil bottle, choose the grade on the same figures as a detergent bottle and confirm it with bottles filled with the oil itself.

Newsletter Updates

Enter your email address below and subscribe to our newsletter